Summary
Inspect, maintain and complete repairs on CNG and/or LNG fueling equipment, including compressors, dispensers, priority panels, dryers, storage tanks and other related equipment. Service Technician III will identify and repair mechanical and electrical corrective service orders identified during inspections, preventative maintenance service orders or escalated service orders from Service Tech I and II on CNG / LNG equipment. Service Tech III will lead major overhauls, rebuilds and startups, with the support of other Service Techs with minimal supervision. Service Technician III will mentor and assign work to Level I and Level II Service Techs.
Essential Duties and Responsibilities include the following. Other duties may be assigned.
Electrical:
Inspect, maintain, troubleshoot, repair or replace electrical equipment such as but not limited to electrical wiring, conduit, panels, switch gear, switches, gauges, transducers, solenoids, gas dryers, actuators, motors, meters, frequency drives and controls for safe and proper operating condition.
Must have a strong working knowledge and be able to demonstrate ability to diagnose and repair electrical problems such as current overloads, ground faults, open circuits and faulty relay logic, also should be able to monitor, check and correct phase imbalances, current draw, low voltage power supply’s, pressure transmitters, relay logic and programmable logic control operation.
Mechanical:
Inspect, maintain, troubleshoot, repair or replace mechanical CNG / LNG equipment such as but not limited to, compressors pumps, engines, intercoolers, after coolers, heat exchangers, piping, tubing, fittings, filters, traps, gas dryers, fasteners, valves and actuators for safe and proper operating condition.
Must have a strong working knowledge and be able to demonstrate the ability to diagnose and repair such mechanical problems as high and low pressure gas flow restrictions, interstage gas compressor temperatures and pressures, pressure regulator variance and should be have a strong understanding and be able to monitor, interpret, check and correct operational trends in reciprocating and screw type gas compressors.
General:
Repair, replace, and adjust malfunctioning equipment to restore proper operating condition specified in regulations and repair manuals.
May perform periodic inspections of fueling stations including all equipment to determine proper and normal operating conditions. Check and record operational data such as fluid levels, temperatures and pressures, compare to trends and have the ability to make corrections as needed.
Detect and correct faulty and malfunctioning mechanical and electrical components, devices and equipment related to “Compressed Natural Gas” (CNG), “Liquefied Natural Gas” (LNG) and “Hydrogen” fueling equipment.
Clean and maintain fueling locations by: picking up trash, emptying trash cans and dumpsters, hand cleaning and polishing of fueling equipment, painting, canopy, lot, islands, surrounding landscaping, in and outside of enclosures.
Update and document all activity, service orders, work performed and recommendation in our Field Service Automation software. Must be thorough and comfortable working on computer and tablets.
Install, remove and modify fueling station equipment as assigned by supervisor.
Maintain all fueling station equipment and structures in accordance with manufacturers and Clean Energy guide lines.
Lead responsibilities as assigned.
Drives to or between company sites to perform job responsibilities.
Other duties as assigned.
Supervisory Responsibilities
This position has no supervisory responsibilities.
Qualifications
To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
Education and/or Experience
High School Diploma or equivalent, 6-9 years of related experience and/or training; or equivalent combination of education and experience.
- Must have basic Mechanical or Electrical basic / foundation knowledge
- Must have basic computer knowledge, especially using service software
Language Skills
Ability to read and comprehend instructions, policies and procedures, correspondence, and memos. Ability to write correspondence. Ability to effectively present information in one-on-one and small group situations to customers, clients, and other employees of the organization.
Mathematical Skills
Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals. Ability to compute rate, ratio, and percent and to draw and interpret bar graphs.
Reasoning Ability
Ability to apply common sense understanding to carry out detailed but uninvolved written or oral instructions. Ability to deal with problems involving a few concrete variables in standardized situations. Ability to use logic and reasoning.
Computer Skills
Basic knowledge of Microsoft Office applications.
Certificates, Licenses, Registrations
Valid driver’s license and clean driving record required.
Summary
Inspect, maintain and complete repairs on CNG and/or LNG fueling equipment, including compressors, dispensers, priority panels, dryers, storage tanks and other related equipment. Service Technician III will identify and repair mechanical and electrical corrective service orders identified during inspections, preventative maintenance service orders or escalated service orders from Service Tech I and II on CNG / LNG equipment. Service Tech III will lead major overhauls, rebuilds and startups, with the support of other Service Techs with minimal supervision. Service Technician III will mentor and assign work to Level I and Level II Service Techs.
Essential Duties and Responsibilities include the following. Other duties may be assigned.
Electrical:
Inspect, maintain, troubleshoot, repair or replace electrical equipment such as but not limited to electrical wiring, conduit, panels, switch gear, switches, gauges, transducers, solenoids, gas dryers, actuators, motors, meters, frequency drives and controls for safe and proper operating condition.
Must have a strong working knowledge and be able to demonstrate ability to diagnose and repair electrical problems such as current overloads, ground faults, open circuits and faulty relay logic, also should be able to monitor, check and correct phase imbalances, current draw, low voltage power supply’s, pressure transmitters, relay logic and programmable logic control operation.
Mechanical:
Inspect, maintain, troubleshoot, repair or replace mechanical CNG / LNG equipment such as but not limited to, compressors pumps, engines, intercoolers, after coolers, heat exchangers, piping, tubing, fittings, filters, traps, gas dryers, fasteners, valves and actuators for safe and proper operating condition.
Must have a strong working knowledge and be able to demonstrate the ability to diagnose and repair such mechanical problems as high and low pressure gas flow restrictions, interstage gas compressor temperatures and pressures, pressure regulator variance and should be have a strong understanding and be able to monitor, interpret, check and correct operational trends in reciprocating and screw type gas compressors.
General:
Repair, replace, and adjust malfunctioning equipment to restore proper operating condition specified in regulations and repair manuals.
May perform periodic inspections of fueling stations including all equipment to determine proper and normal operating conditions. Check and record operational data such as fluid levels, temperatures and pressures, compare to trends and have the ability to make corrections as needed.
Detect and correct faulty and malfunctioning mechanical and electrical components, devices and equipment related to “Compressed Natural Gas” (CNG), “Liquefied Natural Gas” (LNG) and “Hydrogen” fueling equipment.
Clean and maintain fueling locations by: picking up trash, emptying trash cans and dumpsters, hand cleaning and polishing of fueling equipment, painting, canopy, lot, islands, surrounding landscaping, in and outside of enclosures.
Update and document all activity, service orders, work performed and recommendation in our Field Service Automation software. Must be thorough and comfortable working on computer and tablets.
Install, remove and modify fueling station equipment as assigned by supervisor.
Maintain all fueling station equipment and structures in accordance with manufacturers and Clean Energy guide lines.
Lead responsibilities as assigned.
Drives to or between company sites to perform job responsibilities.
Other duties as assigned.
Supervisory Responsibilities
This position has no supervisory responsibilities.
Qualifications
To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
Education and/or Experience
High School Diploma or equivalent, 6-9 years of related experience and/or training; or equivalent combination of education and experience.
- Must have basic Mechanical or Electrical basic / foundation knowledge
- Must have basic computer knowledge, especially using service software
Language Skills
Ability to read and comprehend instructions, policies and procedures, correspondence, and memos. Ability to write correspondence. Ability to effectively present information in one-on-one and small group situations to customers, clients, and other employees of the organization.
Mathematical Skills
Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals. Ability to compute rate, ratio, and percent and to draw and interpret bar graphs.
Reasoning Ability
Ability to apply common sense understanding to carry out detailed but uninvolved written or oral instructions. Ability to deal with problems involving a few concrete variables in standardized situations. Ability to use logic and reasoning.
Computer Skills
Basic knowledge of Microsoft Office applications.
Certificates, Licenses, Registrations
Valid driver’s license and clean driving record required.
